The article below relating to A Step-by-Step Guide to Installing a Bathtub is absolutely interesting. You should check it out.
Installing a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old bathtub is conveniently obtainable, the task can move immediately; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to leave the old tub and embeded in the brand-new one. See to it you have qualified yourself for the job as well as fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This article will certainly help you install a new bathtub in your shower room if you have actually already gotten a new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools as well as product checklist must make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in place in between the tap and the sink. Safeguard the tap in position with the supplier provided backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bath tub up until the level reads degree.
To install taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water and examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub and likewise examine the overflow outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait till the tub has been used at the very least when as this will resolve it into its final position.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to problems with dampness and also possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can break relatively very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on How to Install a Bathtub? Make a remark down the page. We would be delighted to hear your ideas about this write up. We hope that you come back again before long. For those who enjoyed reading our blog posting plz do not forget to share it. I am grateful for your time. Don't forget to come by our blog back soon.
Ready anytime, dial!